![]() Link/ether 70:ca:9b:ce:67:ae brd ff:ff:ff:ff:ff:ff This command will list the interface status, MAC address, MTU size, etc.ġ: lo: mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000 The number next to link/ether is the MAC address. The second way to find MAC address is using “ ip link show” command. ![]() TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0ĭevice memory 0xb1960000-b197ffff Find MAC address with ip link show command in Linux So that this value will be taken as the permanent MAC address of the network interface. Add MACADDR directive and specify the required MAC address to the /etc/sysconfig/network-scripts/ifcfg-ethX network configuration. Stay tuned with It’s FOSS for more Linux tutorial and tips.Inet 10.124.202.230 netmask 255.255.255.128 broadcast 10.124.202.255Įther 70:ca:9b:ce:67:ae txqueuelen 1000 (Ethernet) If you are not trying to rename your Rhel 7 network devices to ethX style, please see below resolution. You have successfully changed the MAC address in true Linux style. Now, verify new MAC address: ip link show enp0s31f6 Next, set the new MAC using command: sudo ip link set dev enp0s31f6 address XX:XX:XX:XX:XX:XXįinally, turn the network back on with this command: sudo ip link set dev enp0s31f6 up I would recommend using Macchanger but if you don’t want to use it, there is another way to change the MAC address in Linux.įirst, turn off the network card using command: sudo ip link set dev enp0s31f6 down Alternatively, follow this link to check your Local. Method 2: Changing Mac address using iproute2 Currently, to view an IP address on your RHEL 7 system enter the following linux command: From the above output we can see that the network interface name is enp0s3 and the configured IP address for this interface is 10.1.1.110 with mask 255.0.0.0 and broadcast IP address is 10.255.255.255. ![]() You can always check the man page for more details. Once you reboot the system, the changes will be automatically lost, and the actual MAC address will be restored again. Where XX:XX:XX:XX:XX:XX is the new MAC id that you want to change.įinally, to revert the MAC address to its original hardware value, run the following command: macchanger -p enp0s31f6 To change the MAC address to a specific value, specify any custom MAC address using command: macchanger -mac=XX:XX:XX:XX:XX:XX You will now see that MAC has been spoofed. Now, to assign any random MAC address to this network card, use: sudo macchanger -r enp0s31f6Īfter changing the MAC id, verify it using command: ip addr #HOW TO CHECK MAC ADDRESS IN RHEL HOW TO#How to Use Macchanger to change MAC addressĭo you remember your network interface name? You got it in the Step 1 earlier. So, choose No (by pressing tab key) and hit Enter key to continue. I recommend not to run it automatically, unless you really need to change your MAC address every time. This gives a new MAC address whenever you attach an Ethernet cable or re-enable WiFi. Important! You’ll be asked to specify whether macchanger should be set up to run automatically every time a network device is brought up or down. ![]() #HOW TO CHECK MAC ADDRESS IN RHEL INSTALL#On Debian, Ubuntu, Linux Mint, Kali Linux: sudo apt install macchanger On Fedora, CentOS, RHEL: sudo dnf install macchanger On Arch Linux or Manjaro: sudo pacman -S macchanger It is available in almost all GNU/Linux operating systems and you can install is using the package installer of your distribution. Macchanger is simple utility to view, modify, and manipulate MAC addresses for your Network interface cards. Method 1: Change MAC address using Macchanger So either try this method on an additional card or be prepared to restart your network. If you do this on a network interface which is currently in use, probably your network connection will be terminated.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |